Accessory Product

DBx Module

Ultra high-performance add-on module delivering unprecedented precision and long-term stability

The DBx Module is a series connected add-on module for MagnaDC programmable DC power supplies, which contains an ultra-high precision, high stability temperature-stabilised control loop, that monitors voltage and current to drive the power supply with any necessary error correction, offering unprecedented high-power performance. Available in a variety of configurations at various ratings, the DBx Module allows Magna-Power products to the requirements for even the most demanding applications.

Key Features

  • Add-on module for MagnaDC power supplies
  • Available from 1.5 kW to 3,000 kW+
  • As low as <10 ppm stability
  • Up to 24-bit resolution
  • Up to 10x output ripple reduction
  • Many configurations
  • Current ratings up to 10,000 Adc
  • Voltage ratings up to 1,000 Vdc
  • Voltage, current, and power control
Magna-Power Expert

Talk with an expert

•
•

Applications

Paired with a MagnaDC programmable DC power supply, the DBx Module provides a broad range of magnet power supply solutions for high-energy physics and medical applications, including driving dipole, quadrupole, and steering magnets and powering coils to establish stable magnetic fields. The high power density of the combined solution, together with its high accuracy and low ripple, also makes it well suited to ATE calibration.

Magnet Steering

Drive highly inductive loads in current mode control for high-energy physics, magnet steering for particle accelerators, radiology research, and advanced cancer therapies.

Calibration and Metrology

High-power voltage and current references, with up to 24-bit precision and extremely low temperature coefficients, provide R&D and ATE calibration solutions for DC-input devices.

For the design and measured results, read the white paper Improving Output Performance of Switching Power Supplies Using the New DBx Module.

Choose Your Configuration

The DBx Module is offered in three configurations, A1, B1, and C1, which differ in maximum current capability and internal stages.

Configuration A1: Ripple Filtering + High Stability

Configuration A1 contains every stage: the linear regulator, the differential-mode and common-mode DC EMI filters, the temperature-stabilized ultra-high stability controller, and the DCCT, in a 1U (1.75" high) rack-mount enclosure.

Configuration B1: High Stability

Configuration B1 is intended for applications that do not require additional DC filtering. It contains only the temperature-stabilized ultra-high stability controller and the DCCT, in a 1U rack-mount enclosure.

Configuration C1: High Current with External Transducer

Configuration C1 is intended for high-current applications. Its 1U rack-mount enclosure contains only the temperature-stabilized ultra-high stability controller, and a provided external DCCT ties into the DBx Module through a rear connector. For high-power MT Series systems from 100 kW to 3,000 kW+, the DBx Module can be fully integrated inside the MT Series enclosure.

Configuration Comparison

 A1B1C1
EMI and ripple filteringYesNoNo
High stability, precision, and accuracyYesYesYes
Current transducerInternal DCCTInternal DCCTExternal DCCT
Long-term stability (8 hr)< 10 ppm< 10 ppm< 50 ppm
Maximum voltage ratings6 to 1,000 Vdc5 to 1,000 Vdc5 to 1,000 Vdc
Maximum current ratings3.75, 7.5, 15, 30, 50, 75, or 150 Adc3.75, 7.5, 15, 30, 50, 75, or 150 Adc500, 750, 1,500, 3,000, 5,000, or 10,000 Adc
Form factor1U enclosure1U enclosure1U enclosure + external transducer
Best suited forApplications that need the lowest output ripple as well as high stabilityApplications that do not require additional DC filteringHigh-current applications, including MT Series systems

Low Ripple Performance

Configuration A1 uses three filter stages to suppress differential line-to-line EMI, common-mode line-to-ground EMI, and power supply ripple from the DC bus, reducing output ripple by up to 10x.

Power supply output ripple without (left) and with (right) the DBx Module Configuration A1.
Power supply output ripple without (left) and with (right) the DBx Module Configuration A1.
Power supply output ripple without (left) and with (right) the DBx Module Configuration A1.

EMI filtering: internally fabricated common-mode and differential-mode EMI filters provide insertion loss as high as 62 dB. Typical results from 0 to 10 MHz are shown below.

Common-mode noise from a TS Series power supply alone (left) and with the DBx Module (right).
Common-mode noise from a TS Series power supply alone (left) and with the DBx Module (right).
Common-mode noise from a TS Series power supply alone (left) and with the DBx Module (right).
Differential-mode noise from a TS Series power supply alone (left) and with the DBx Module (right).
Differential-mode noise from a TS Series power supply alone (left) and with the DBx Module (right).
Differential-mode noise from a TS Series power supply alone (left) and with the DBx Module (right).

Ripple cancellation: to filter power supply output ripple, with components that can extend down to the mains frequency, Configuration A1 uses a linear regulator with a low DC voltage drop across a series-pass power semiconductor. The regulator runs two feedback loops: one maintains a 1.25 Vdc drop across the regulator, and the second produces an AC ripple-canceling voltage across the series-pass semiconductor, equal and opposite to the AC ripple at the input. Series-connected diodes across the regulator protect against current surges and overvoltage transients, a weak point in conventional linear regulators.

For guidance on measuring ripple, read Peak-to-Peak Output Voltage Measurements of Switching Power Supplies.

Stability, Accuracy, and Resolution

An ultra-stable fluxgate direct-current current transformer (DCCT) takes high-accuracy isolated measurements in series with the power supply's DC output. Combined with the DBx Module's low temperature drift resistors and temperature-stabilized digital programming circuit, it provides finely granular programming and readback with excellent long-term stability. Critical components are laid out within a specially designed temperature compartment to shorten the time to temperature stabilization.

  • Long-term stability (8 hr): < 10 ppm for Configurations A1 and B1, < 50 ppm for Configuration C1
  • Temperature coefficient: < 0.05 ppm/°C in voltage control, < 0.5 ppm/°C in current control
  • Resolution: 18-bit programming, 24-bit measurement
  • Accuracy: ±0.04% of full scale, programming and measurement, in voltage and current control

Setup and Control

Configurations A1 and B1 provide copper bus bars with threaded inserts for the DC input and DC output connections. The power supply's DC output connects to the DBx Module's DC input, all current sensing is done inside the DBx Module, and the load or device under test connects to the DBx Module's DC output bus bars. Configuration C1 uses an external DCCT, whose control signal feeds back to the DBx Module through its external user I/O connector.

In every configuration, a provided cable connects the DBx Module's interface connector to the power supply's JS1 37-pin external user I/O connector, so the DBx Module can control the power supply.

Programming: set points, trip points, and slew rates are programmed through the DBx Module, using the front panel knob or keypad, the front panel up and down arrows for single-bit adjustments, or the computer interfaces with the provided MagnaWEB software or user-defined software using SCPI commands. RS485 and front and rear USB are standard; LXI TCP/IP Ethernet is optional.

Master/slave systems: when power supplies operate in master/slave, the UID53 Universal Interface Device provides a dedicated breakout connector and module interface cable, so the DBx Module integrates with the power supply while it remains part of the master/slave system.

Model Ordering Guide

DBx Module models are defined by the configuration type and number, the maximum voltage rating, and the maximum current rating. Voltage ratings follow Magna-Power's standard MagnaDC power supply offering. Because the DBx Module's resolution step size and calibration are a function of its maximum ratings, specify the model most closely matched to the requirement.

Specifications are subject to change without notice. Unless otherwise noted, all specifications measured at the product's maximum ratings.

Performance Specifications

Stability, A1 and B1 Configuration
Full width at half maximum (FWHM)
Voltage or Current Control
< 10 ppm; long-term drift (8 hr)
Stability, C1 Configuration
Full width at half maximum (FWHM)
Voltage or Current Control
< 50 ppm; long-term drift (8 hr)
Temperature Coefficient
Voltage Control
< 0.05 ppm/°C
Temperature Coefficient
Current Control
< 0.5 ppm/°C
Rise/Fall Time
Maximum
Voltage Mode: 6 s, 10% to 90% full scale voltage rating
Current Mode: 6 s, 10% to 90% full scale current rating
Power Mode: 6 s, 10% to 90% full scale power rating
Power Loss
Configuration A1 Only
Current output x 1.5 volts
Warm-up Time
45 min

Programming Specifications

Programming Resolution
18-bit
Measurement Resolution
24-bit
Accuracy
Programming and Measurement
± 0.04% of full scale; voltage control
± 0.04% of full scale; current control

Connectivity Specifications

AC Input
1Φ, 2-wire + ground
IEC 60320 connector
AC Input
3Φ, 3-wire + ground
Molex 38660 connector
DC Input
Bus bars with 3/8" threaded insert; 250 Adc max
DC Output
Bus bars with 3/8" threaded insert; 250 Adc max
Communication Interfaces
Standard
USB Host (Front): Type B
USB Host (Rear): Type B
RS485 (Rear): RJ-45
External User I/O: 15-pin D-Sub, female
Communication Interfaces
Optional
LXI TCP/IP Ethernet (Rear): RJ-45

Physical Specifications

Size and Weight
Configuration A, Configuration B
1U
1.75” H x 19” W x 24” D (4.4 x 48.3 x 61.0 cm)
35 lbs (15.88 kg)
Size and Weight
Configuration C
1U (See Above) + External Transducer
External transducer size and weight will vary depending on current rating

Environmental Specifications

Ambient Operating Temperature
0°C to 50°C
Storage Temperature
-40°C to +85°C
Humidity
Relative humidity up to 95% non-condensing
Air Flow
Side intake, rear exhaust
EMC
Complies with 2014/30/EU (EMC Directive)
CISPR 22 / EN 55022 Class A

Regulatory Specifications

CE Mark
Yes
RoHS Compliant
Yes

Documentation

DBx Module User Manual [0.012] [EN] [PDF]

Software

MagnaCTRL Software [0.017-77809] [MSI]