Firmware xGen 0.068

• Fixed:

  Introduction to system ratings causing multi-module systems (e.g. ALx racks) to fault.

  GEN2-4335

MagnaCTRL 0.003

• Fixed:

  Prevent user from operating product when EEPROM is patching/

  GEN2-4321
• Fixed:

  Program was freezing during initialization due to wrong logic in the Message Scheduler.

  GEN2-4330

Test & Cal Suite (Internal) 0.046

• Fixed:

  Selected correct firmware when gaps in versions.

  GEN2-4318
• Feature:

  Add calibration routines for Line Phase Loss.

  GEN2-4316

Firmware xGen 0.067

• Feature:

  Master-slave functionality

  GEN2-4289, GEN2-4211, GEN2-4166
• Feature:

  Mask faults via Magna-Power provided EEPROM patches

  GEN2-4249
• Feature:

  Measure local current when in multi-module and in master-slave operation

  GEN2-4056 (23080R42)
• Feature:

  Setup and configure master-slave from the front panel menu system

  GEN2-4165, GEN2-4219
• Feature:

  Include aggregate system ratings in the about menu

  GEN2-4168
• Fixed:

  Eliminate fan fault under certain start-up/set-point conditions

  GEN2-4144
• Improved:

  System faults when slave(s) communications are severed

  GEN2-2722
• Improved:

  Factory programmable voltage levels for low AC-line fault

  GEN2-4208
• Improved:

  Automatically dim VFD and LED to extend their life, when not in use

  GEN2-4056

Test & Cal Suite (Internal) 0.045

• Improved:

  Catch condition where thermal couple readout is low

  GEN2-4297

Documentation 0.25

• Improved:

  Expansion and clarification of industrial communication protocols

  GEN2-4106

Communications NI LabVIEW Driver 1.0.0

• Feature:

  LabVIEW drivers for xGen MagnaDC approved by NI

  GEN2-3971
• Feature:

  Added Lock

  GEN2-4169
• Fixed:

  Measure signal and control ordering

  GEN2-3542, GEN2-3144
• Fixed:

  Voltage and current reads timed out after *RST

  GEN2-4171
• Improved:

  Add driver installation instructions to README

  GEN2-3380
• Maintenance:

  Re-organize file naming for multiple product families and generations

  GEN2-4170

MagnaCTRL 0.002

• Feature:

  Implement system ratings in menus and number scalings

  GEN2-4285
• Fixed:

  Reduce screen buffer size for logs to conserve memory

  GEN2-4305
• Fixed:

  Save log file in the application path

  GEN2-4298

Communications 0.058

• Feature:

  Added EtherNet/IP EPS driver, which includes all commands both implicit and explicit, and EtherNet/IP UDT drivers for Input/Output Assemblies.

  GEN2-3476, GEN2-3477
• Feature:

  Show MAC address on front panel for industrial communication options.

  GEN2-3438, GEN2-3323

Firmware xGen 0.065

• Feature:

  Monitor temperature on output capacitors, which could be caused by excessive load ripple, protecting them from premature failure.

  GEN2-3141, ENG-4692
• Feature:

  Added Programming Line Fault detection, which triggers if User I/O signals exceed 110% of maximum allowed value.

  GEN2-3131, GEN2-3332
• Feature:

  Fan control and monitoring improvements with PWM control, tachometer feedback, and rotor fault

  GEN2-3683, ENG-5051, GEN2-4093
• Feature:

  Gain scheduling on inner chopper feedback compensator for improved ripple and stability under various loads.

  GEN2-3907, GEN2-3896
• Feature:

  Maximum slew rate now user/factory programmable in EPROM, laying groundwork for High Slew Rate (+HS) option.

  GEN2-3962
• Feature:

  Added chopper stage hard and resetting soft trip states (burp mode)

  GEN2-4044
• Fixed:

  Disable Modbus protocol when other LXI and industrial interfaces are active. Modbus available for standard USB and RS485 interfaces only. 

  GEN2-2974
• Fixed:

  Master and slave instantaneous current matching.

  GEN2-2786, GEN2-3229, ENG-2086 (23080R42)
• Fixed:

  Stability improvement for front panel firmware upgrades.

  GEN2-3593, GEN2-3874
• Fixed:

  Switching to Function Generator now retains set points.

  GEN-3858
• Fixed:

  Independent fault timers for handling simultaneous faulting.

  GEN2-3916
• Improved:

  Completed syntax for SCPI query SYSTem:ERRor[:NEXT]?

  GEN2-4176
• Improved:

  Front panel status messages now vary between MagnaDC and MagnaLOAD products.

  GEN2-3942
• Improved:

  Expand status register to 64 bits.

  GEN2-2958, GEN2-3777, GEN2-3866
• Improved:

  Modifications to EEPROM read/write settings and visibility to allow editing EEPROM in MagnaCTRL.

  GEN2-3704
• Changed:

  Aggregate temperature faults, create soft and hard fault groups in STAT:QUES:COND?

  GEN2-4186

MagnaCTRL 0.001

• Feature:

  Initial release of MagnaCTRL for SLx Series with core functionality, including: dashboard with multi-product control, EPROM editor, firmware update, and product explorer. 

  GEN2-3579

Documentation 0.002

• Feature:

  Added out of regulation and below minimum voltage faults.

  GEN2-3441
• Feature:

  Added EtherNet/IP documentation with full command list for Implicit/Explicit messaging.

  GEN2-3252
• Fixed:

  Corrected parameter order for SCPI Command SCPI CONF:CONT. 1 (Current) | 2 (Voltage) | 3 (Power) | 4 (Resistance) | 5 (Rheostat) | 6 (Shunt Regulator)

  GEN2-3143
• Improved:

  Updated Remote Sense documentation for revised functionality.

  GEN2-3439
• Removed:

  IEEE-488 GPIB now documented only for ALx Series MagnaLOADs and Gen1 products.

  GEN2-4175

MagnaWEB 0.44

• Fixed:

  Overflowing serial buffer on MagnaWEB communications drivers. Buffer now flushed before sending *IDN? query during protocol check.

  [GEN2-3898]

Test & Cal Suite (Internal) 0.43

• Improved:

  Test report now generated for diagnostic test, for use in validation tickets

  [GEN2-3893]
• Fixed:

  Test and store calibration records on replacement control boards.

  [GEN2-3823]
• Changed:

  Created option to enable more intensive (conditional) testing on reworked products and repairs.

  [GEN2-4085]